INFINIUM PORTABLE DIGITAL LASER HAIR REMOVER

SKIN IRRADIATION TEST
If you are using this product for the first time or have recently tanned, you should perform skin tests on each area to be irradiated. Skin tests are used to check whether the skin reacts to radiation and to determine the appropriate light intensity for each part of the body.
1. Select an area close to the area to be irradiated. Caution: Do not attempt to use this product on difficult or sensitive areas (ankles or bones).
2. Press and hold the on/off button for 1 second to turn on the device, making sure that level 1 is selected.
3. Place the device perpendicular to the skin (at a 90° angle) so that the light output is in direct contact with the skin.
4. Press the flash button to emit a flash.
5. Slide the device over the skin to the next area to be irradiated.
6. Gradually increase the intensity levels, emit a flash, and then slide the device to the next position. Repeat this operation for all levels within the light intensity range recommended for your skin type.
7. After the skin test, check the condition of the skin after 2 hours. If there are no abnormalities (redness or blisters) in the irradiated area, you can use this product with confidence.

TIPS FOR USE
1. HAIR REMOVAL FROM THE UNDERARM AREA • Before hair removal, clean the underarms of any antiperspirant, deodorant, perfume, cream or other cosmetics applied to the underarm area. • In areas with loose skin, stretch the skin with your fingers before removing hair. It is normal for the skin to experience a slight burning sensation when exposed to IPL flashes.
2. BIKINI AREA HAIR REMOVAL • For areas with accumulated pigmentation and dark colours, use the lowest speeds. Before adjusting, use the first speed. • In areas with loose skin, stretch the skin with your fingers before removing the hair. It is normal for the skin to experience a slight burning sensation when exposed to IPL flashes.
3. HAIR REMOVAL ON HANDS AND FEET • Bones and uneven areas are more prone to pain than other parts.
4. IMPORTANT • Areas with burn marks, dark areas, around the eyes, areas with frostbite, moles, eyebrows, hair, sunburn, etc. • After hair removal, avoid exposing the area to ultraviolet rays for 48 hours to prevent the sun from burning the skin during hair removal. • Do not look directly at the flash when the IPL hair removal device is in operation.

USE AND OPERATION
1. Shave the hair in the area to be treated, clean and dry it before using the device. Never use flammable liquids such as alcohol (including perfumes, deodorants or any other preparations containing alcohol) or acetone to clean your skin before using the hair removal device. This could cause a temporary change in pigmentation.
2. Connect the hair removal device to the power adapter.
3. Essential: Put on the protective goggles included with the product (to reduce damage to the eyes caused by the hair removal flashes).
4. Press and hold the on/off button for 1 second to turn on the device. The internal fan will start running, a sound will be heard and the relevant parameters will be displayed on the screen. Press the button again to change the intensity level if desired.
5. Align the light output of the instrument with the area you wish to treat. When the induction indicator light turns on, you can press the Flash button to begin. (Press and hold the flashing button for 3 seconds to enter/exit automatic flashing mode).
6. Briefly press the power/level change button to adjust the levels (level 1 is the lowest and level 9 is the highest) and select the appropriate level according to your skin and hair colour.
7. Place the device perpendicular to the skin (90º) with the light output window always in contact with the area of skin you wish to treat. When the induction indicator light comes on, press the flash button and the device will start flashing.
8. Do not fire more than once in the same area or position, as this can easily cause skin damage or burns. Slide the device with each flash.
9. When you have finished, press and hold the power button for 2 seconds to turn off the device.
10. The lamp head can be cleaned with an alcohol-free wet wipe or a soft cloth to clean the light outlet window. After cleaning, replace the hair removal device and adapter in the packaging box.
11. In manual mode, you must press the flash button each time you want to emit a flash of light. This mode has precise control, ideal for areas where the device needs to be repositioned and more delicate areas.
12. In automatic mode, the flash will fire at regular intervals. You only need to slide the device over the skin in time with the flash intervals. This mode is more suitable for use on large areas of skin such as the legs.
CARE INSTRUCTIONS FOR THE USER
Interval of use: • 1–2 times per week for weeks 1–4. • Once per week for weeks 5–8. • Once